Contact Us

Use the form on the right to contact us.

You can edit the text in this area, and change where the contact form on the right submits to, by entering edit mode using the modes on the bottom right. 

         

123 Street Avenue, City Town, 99999

(123) 555-6789

email@address.com

 

You can set your address, phone number, email and site description in the settings tab.
Link to read me page with more information.

Blog

 

 

Filtering by Category: Tutorial

Tutorial: Brighton Mini Quilt Decorative Pillow/Cushion Cover Hack

Niina Kivelä

Brighton Pillow 2.jpeg

Blogger: Sarah Scott from Piccolo Studio

Brighton Pillow/Cushion Cover

The following steps apply after the Brighton mini quilt has been quilted, but not bound. In addition to the fabric requirements for the mini quilt, you will also need 3/4 yard of coordinating quilting cotton and a 20” decorative pillow/cushion insert.

Cutting Instructions

Cut 2 rectangles 22” x 15” using the coordinating quilting cotton.

Assembly Instructions

Trim the mini quilt top to size – 19 1/2” x 19 1/2”. Set aside.

brighton.jpg

Take the 2 rectangles and hem one long side (22”) of each piece. To hem, fold the long edge 1/2” wrong sides together. Press. Fold it another 1/2’’. Press. Sew to secure the hem.

envelope back 1-100.jpg

Place the mini quilt top right side down on the cutting mat. Lay the two rectangles right side up, on top of the mini quilt top, allowing them to overlap each other by 5” in the middle. Place a pin in the center to hold all 3 pieces together.

NOTE: The bottom rectangle piece shown larger than actual cutting size to show placement. The two pieces will line up equally on each side.

envelope back 2-100.jpg

Very carefully, turn the pieces over without dislodging them. Pin securely around the edge, making sure the overlapping fabrics on the back have stayed flat.

envelope back 3-100.jpg

Stitch around the quilt top 1/4” from the edge, removing pins along the way.

envelope back 4-100.jpg

Cut off the excess backing pieces.

envelope back 5-100.jpg

Bind as per the pattern.

Insert the cushion insert into the decorative pillow/cushion cover.

Brighton pillow 1.JPG







Tutorial: Geneva Bonnet with Pintucks

Niina Kivelä

Geneva Bonnet with pintucks.jpg

Blogger: Kate Golden

Geneva Bonnet with Pintucks

Following the directions for the lined bonnet in the Geneva Bonnet Pattern:

When cutting pattern pieces, cut one lined bonnet piece, and one that is 2.25” longer along the short side. For example, if your first piece is 5 ½ x 12, your second will be 7 ¾ x 12.  This tutorial will add 4 pintucks to the front side of the bonnet.  If you would like more, add an additional ½ “ when cutting this piece. 

For the longer bonnet piece, use a removable marking tool to mark a line 1 ¼ “ from the front edge down the long side. 

Pic 1.jpg

Mark 3 additional lines 1” apart.

Pic 2.jpg

Wrong sides together, fold along the first line you marked.  I used a pen that removes when heated, so I finger pressed along the line.  Depending on how you marked this line, you could also press with an iron.

Pic 3.jpg

Sew a straight line ¼ “ in from this edge.

Repeat folding the fabric along the other 3 lines, wrong sides together, and then sewing with a ¼ “ seam allowance. 

Pic 4.jpg

Press the pintucks forward toward the front of the bonnet.

Pic 5.jpg

Baste the pintucks down along the side seams.

Follow the remainder of the directions as instructed in the lined bonnet tutorial.

Shown here the Geneva Bonnet with pintucks paired with the Avonlea Romper.

Tutorial: Adding Belt Loops to the Newport Shorts

Niina Kivelä

Newport shorts with belt tutorial.jpg

Blogger: Natasha Chrismas

A fun addition to the Newport Shorts is to add belt loops and a fabric sash, creating a whole new look. When making the Newport Shorts, follow the steps as instructed up to Constructing the Waistband in the pattern. Follow these additional steps to add the belt loops to the waistband front and back before the first step in this section:


Creating the Belt Loops

Cut a strip of fabric 2’’ wide by 11’’ long. The length of this strip is suitable for all sizes. 

Blog Newport photo 1.jpg

Fold the piece of fabric in half, aligning the long raw edges, wrong sides together. Press to make a crease.

Blog Newport 2.jpg

Open the fold and bring the long raw edges in to meet the center crease. Press. 

Blog Newport 3.jpg

Fold in half again, bringing the long folded edges together and press. The piece is now 1/4 its original size. Topstitch the long folded edge, using a 1/8’’ seam allowance, to secure it closed.

Blog Newport 4.jpg

Topstitch the remaining long edge using a 1/8’’ seam allowance.

Blog Newport 5.jpg

Cut the fabric into 3 pieces, matching the height of the waistband size being sewn. For example, size 3 will be 2 3/4’’.

Blog Newport 6.jpg

Find the center of the back waistband by folding it in half. Press to create a memory crease. Place one belt loop over the center position with the wrong side of the belt loop touching the right side of the waistband. Pin in place. Using a 1/8’’ seam allowance, baste in place at the top, and bottom of the fabric.

Blog Newport 7.jpg

Find the center of the front waistband by folding in half right sides together. Press to create a memory crease.

Blog Newport 8.jpg

Fold the waistband in half again. Press to create another memory crease.

Blog Newport 9.jpg

Unfold the waistband. Place the belt loops over the crease created on each side of the center crease. The wrong side of the belt loop will be touching the right side of the front waistband. Using a 1/8’’ seam allowance, baste in place at the top, and bottom of the fabric.

Blog Newport 10.jpg

Continue with the instructions for Constructing the Waistband per the pattern.

Constructing the Sash

Cut 2 pieces of fabric according to the chart below.

Blog Newport Chart.png

Place the two pieces right sides together and sew one short end with a 1/2’’ seam allowance.

blog sash.jpg

Press the seam open.

Blog Sash 2.jpg

Fold the fabric in half, right sides together. Press.

Blog sash 3.JPG

Trim the edge of each end of the fabric at a 45 degree angle.

blog sash 4.jpg

Sew around the raw edges of the sash with a 1/4’’ seam allowance. Leave a 2” opening in the middle for turning.

Blog sash 5.jpg

Clip the corners.

Blog sash 6.jpg

Turn the sash right side out using a turning tool of your choice. Press.

Blog sash 7.JPG

Pin the 2” opening closed. Topstitch around the sash to close the 2” gap.

Blog sash 8.JPG
Blog Islington Girl top.jpg