Contact Us

Use the form on the right to contact us.

You can edit the text in this area, and change where the contact form on the right submits to, by entering edit mode using the modes on the bottom right. 

         

123 Street Avenue, City Town, 99999

(123) 555-6789

email@address.com

 

You can set your address, phone number, email and site description in the settings tab.
Link to read me page with more information.

Blog

 

 

Tutorial: Full Bust Adjustment

Niina Kivelä

Blogger: Jenn Meitin Williams

Full Bust Adjustment

With the release of the women’s Jersey Romper and Dress, we thought it would be a good time to provide a quick tutorial on how to do a Full Bust Adjustment (or FBA) for a knit top.  If you are new to the concept of an FBA, let us enlighten you!  A FBA is needed when your full bust measurement is a different size than your upper bust measurement.

1.jpg

For example, if a full bust measures a size 8 but the upper bust measures a size 4, then a FBA is needed. If you make a size 8 based on the full bust measurement, chances are the rest of the bodice will be way too big.  If you choose a size 4 based on the upper bust, then there will be pulling across the bust as the fabric stretches to fit.  Alternatively, simply grading out for the bust will not give you a proper fit. If desired, make a muslin of the bodice based on your full bust and see how it fits.  If there is gaping at the armscye or it is too big across the upper bust then try this FBA method!

Let´s get started!

First, measure your chest accurately and with a bra.  Make sure the tape measure is taught but not tight.  It may be helpful to have someone help you measure so you can stand upright with arms relaxed by your side.

Once you have bust measurements, choose your size based on your upper bust measurement and cut out that bodice.  (Note, if you need to grade for your waist, make sure you do that first.)

Hold the front bodice pattern piece up to your body and make a mark approximately at your apex (This is a fancy word for your nipple).

2.JPG

Draw a line straight across the bodice -perpendicular to the fold line - through the apex mark.

3.JPG

If using a traced piece of paper, draw in a grainline to match up the pieces later.  The grainline should be parallel to the fold.

4.JPG

Cut the bodice pattern piece at the horizontal line drawn through the apex.

5.JPG

Using a scrap piece of paper, tape it behind the bodice to add some length to the front bodice piece.  Once the scrap paper is taped to the top portion of the bodice, measure down 1-inch from the apex line and make another horizontal line.

6.JPG


Tape the bottom bodice piece along that line making sure to line up the grainline.

7.JPG

At the side seam, make a mark half an inch away from the center of the one-inch length that you added as illustrated below.

8.JPG

Draw a smooth curve from the armscye, through the mark, down to a point approximately 2-inches below the added length.  Please note, it may take a trial or two to get the perfect fit. You may need less of a “bubble” or a little less added length.  Also note, this method really doesn’t work well if adding more than 1-inch of added bust length. Stay tuned for a more involved FBA to be covered in a later tutorial that is better suited for that.

9.JPG

Trim off the excess paper around the new bust “bubble” and at the center fold if necessary.

10.JPG

Now it’s time to cut the fabric! Cut out the front bodice fabric and make two marks where the extra inch was added as indicated by the arrows below.  Cut out the back bodice as-is.  Do not make any changes to the back bodice piece.

11.JPG

Notice that the front and back side seams are not the same length (because length was at the bust.) This is ok; we will be easing the back into the front.

Pin/clip the front and back bodice pieces right sides together at the side seams.  Start from the bottom and stop pinning when approximately an inch away from the bottom mark.  

12.JPG

Now pin from the top of the side seam until 1-inch away from the top mark.  There will be excess fabric in between the two pins/clips where you stopped pinning. 

13.JPG

Sew the side seam starting at the bottom and when you get to the last pin before the added length (clear clip pictured below); simply stretch the back slightly to make it the same length as the front between the two pins. Sew slowly to attach. This will create a small amount of gathering that will help hold the extra volume in your bust.   Because this gathering is under the arm, it will not be noticeable when wearing.  It will also be stretched over your bust so it really shouldn’t look gathered once you have the garment on.  Once you reach the next pin (orange clip below), finish your side seam up through your armscye. 

That’s it! You did a simple FBA for a knit bodice.  This method may not work for everyone, but it is a simple way to start learning if you need an FBA and it’s an easy method to try. We will be covering a more in depth FBA at a later date!